Plastic pyrolytic oils as renewable fuel: improving its physical properties and ignition patterns by waste renewable source-an experimental analysis.

The increase in plastic products and disposal poses a severe environmental challenge because of their poor biodegradability and undesirable disposal by landfilling. Recycling is the best possible solution to the environmental challenges implemented by the plastic industry. Pyrolysis is a process that converts waste plastics into pyrolytic oil, and it can be used as fuel in a blended form. The viscosity and lubricity of the LDWP (low-density waste polyethylene) pyrolytic oil were lower than standard diesel. Capparis spinosa methyl ester (CME) is blended and experimented with to overcome the lubricity issue of pyrolytic oil. In this investigation, 5%, 10%, and 15% CME were blended with PD20 (20% LDWP oil + 80% diesel) blend on a volume basis. Experiments were conducted to examine the effects of CME on combustion, performance, and emissions using the combination of CME and PD20 blend tested at 0%, 25%, 50%, 75%, and 100% loading conditions. All three ternary mixtures showed enhanced combustion performance and increased NOx and smoke emissions. Due to better combustion, the efficiency of the blend PCD10 (10% CME + 20% LDWP oil + 70% diesel) was higher than the PD20 blend and significantly closer to diesel. Hence, PCD10 is suggested as an alternative to diesel fuel.

Thermal and chemical exhaust gas recirculation potential of punnai oil biodiesel-fuelled diesel engine for environmental sustainability.

Major energy production all over the world depends on fossil fuels. Recent research on alternative energy sources has raised major concerns about environmental impacts, future availability, and cost. Pollution from diesel engines also affects the environment negatively. As a result, there is a worldwide concern about reducing the pollutants emitted by diesel engines. In comparison to diesel fuel, biodiesel combustion produces reduced carbon monoxide (CO2) and unburned hydrocarbon (UHC) emissions but higher nitrogen oxide (NOx) emissions. The current study aims to investigate the thermal and chemical effects of exhaust gas recirculation (EGR) on the features of a diesel engine for environmental sustainability. The punnai oil was produced from kernels of punnai seeds and transesterified in two phases using alcohol with the existence of a catalyst. The higher viscosity of punnai oil biodiesel is diluted by mixing it with diesel fuel. Our previous investigation indicated that neat punnai oil biodiesel is a potential fuel; however, the findings showed that the addition of diesel is necessary to obtain acceptable engine performance. In this study, punnai oil biodiesel was mixed at a rate of 20% with diesel (B20) and run in a diesel engine with varied EGR rates under five different engine loads. This combined impact enhanced the maximum heat release rate (HRR) and maximum combustion pressure, according to the findings. The premixed burning fractions were commonly higher at all engine loads, whereas the diffusion combustion fractions were lower. When the centre of the HRR changed toward the top dead centre (TDC), combustion durations remained rather constant. The experimental results revealed the B20 blend at a 10% EGR flow rate produced 6.57% lower BTE, 37.04% higher BSEC, 2.47% higher EGT, 5.13% lower CO, 31.11% higher CO2, 3.13% higher UHC, 8.36% lower NOx, and 4% higher smoke opacity when compared with diesel in a standard diesel engine.

Performance and environmental impact assessment of diesel engine operating on high viscous punnai oil-diesel blends.

The increasing demand for energy consumption because of the growing population and environmental concerns has motivated the researchers to ponder about alternative fuel that could replace diesel fuel. A new fuel should be cheaply available, clean, efficient, and environmentally friendly. In this paper, the engine operated with neat punnai oil blends with diesel was investigated at various engine load conditions, keeping neat punnai oil and diesel as base fuels. The performance indicators such as brake specific energy consumption (BSEC), brake thermal efficiency (BTE), and exhaust gas temperature (EGT); emission indicators such as carbon monoxide (CO), oxides of nitrogen (NOx), and smoke opacity; and combustion parameters like cylinder pressure and heat release rate were examined. The brake thermal efficiency of diesel is 29.2%, whereas it was lower for neat punnai oil and its blends at peak load conditions. Concerning the environmental aspect, oxides of nitrogen emission showed a decreasing trend with higher smoke emissions for Punnai oil blends. Detailed combustion analysis showed that on smaller concentrations of punnai oil in the fuel blend, the duration of combustion has improved significantly. However, for efficiency and emissions, the P20 (20% punnai oil and 80% diesel) blend performs similar to that of diesel compared to all other blending combinations. When compared with diesel, the P20 blend shows an improvement in BSEC by 26.37%. It also performs closer in HC emission, a marginal increase in smoke opacity of 4% with reduced NOx and CO2 emission of 7.9% and 4.65% respectively. Power loss was noticed when neat punnai oil and higher blends were used due to the high density and low calorific value of punnai oil blends which leads to injecting more fuel for the same pump stroke.